How to Install a Paver Patio

 

how to install a paver patio

A detailed instruction on how I have constructed paver patios and installed pavers over the last 15 years. You can install pavers or do-it-yourself with the step-by-step information on this page. With some patience and work you will have constructed a patio to enjoy for many years. Have fun!


Learn How to Build a Paver Patio!

 

PATIO RESOURCES!
STORE






Bookmark and Share

8 Basic Steps to Paver Patio
Do-it-yourself Construction

1.
The first step is to determine the size or area of the paver patio by square foot. This will figure into the estimate of materials needed later. Mark off the area with a can of white spray paint, slightly larger to allow for paver edge restraints and a footing base at the borders of the patio.

Paver Information


2.
Estimate the materials needed, chose desired pavers, here is a site that describes how to estimate pavers, how many per square feet for some common pavers Shapes & Details of Pavers. Most paver and concrete dealers will let you know how many per square feet for there products. Also estimate base material and sand, approximately 1 1/2 yards of gravel(3/4 " quarry process)per 100 square feet, this will support a 4" compacted base. Sand - a fine mason sand, about 1/4 the amount of the gravel base should be plenty. Having more is always better than not having enough base material.

 

Paver tools 3. Digging and preparing for a good paver base is important and will be the most time consuming process. Excavate by shovel or loader if available, use local digging laws to make sure to avoid any buried cable. Make base 6"-8" below desired height of patio, the pavers will take 2" of that so the gravel base under the pavers will be 4"- 6". If possible use a landscape fabric under gravel for better support and protect base from soil. Some areas may require a deeper base due to poor soil or recent disturbed soil from new house construction. Next - get the gravel base in by wheelbarrow, shovel, loader, and rake it out to approximate level.

Paver Patio Base



Paver Technique

4. Grade the patio base with a 2X4 to get an even and sloped base for water runoff. slope slightly to where desired water should run, use about a quarter bubble technique on a 4 foot level, make sure sloping the correct way. For larger patios, 2 2X4s may be needed so they would have to be nailed together. If your patio is next to a concrete driveway or bordering concrete or timbers, then use a modified 2X 4 to grade along that border(see picture on left). Take the time to get level, and re-grade after compaction is done (next step).

 

 

 

tumbled paver walkway to gazebo

White Gazebo & paver patio walkway


More Information

Paver Plate Compactor 5. Use a plate compactor or like compaction device to get good a solid base for the pavers. If the gravel is too dry, wet it down some with a garden hose to make it pack better. Grade additional times after each compaction until complete.

Paver Mason Sand




Paver Patio Fine Grade

6. Fine grade with mason sand the same way grading was done earlier, this final grade evens out the rough gravel grade and allows for a nice even base for the pavers. This is only a quarter inch or less layer of sand to maintain the proper grade, not an inch of sand like you may have heard of, remember the proper grade and slope has already been done with an easy to work with gravel base.

 

 

12 x 12 gazebo

Lay the Pavers





Paver Diamond Saw

7. Lay the pavers in the desired pattern, for pattern ideas see resource page, get the pavers tight as possible, start from a point or house foundation to allow for the best looking pattern. Keep in mind pavers will need to be cut with a saw and diamond paver blade if patio area has curves or obstacles. simple square patios may not need any cutting. to cut pavers, use a measuring technique or measure with paver in place and mark.

Interested in a gazebo? Constructed of durable rigid resin, the gazebos are basically maintenance-free

Paver Plastic Edge
Paver Patio Example














8. Finally, use a plastic edge restraint and secure with spikes about 2' apart or less for more strength. Then sweep with the same mason sand, the finer the better, it will sweep into the cracks and be a dry mortar so to speak and secure the pavers. The dryer the sand, the easier it will be to sweep in. Use the compactor to pack the paver patio and allow the sand to fall in the cracks better. I would suggest to put cardboard or fabric under the compactor to not damage pavers and stop the vibrating noise too, I bungee cord cardboard to the bottom of the compactor, however after a few times the cardboard will be worn, but will work for a single use. Sweep sand again until the paver joints will take no more sand. And the last thing would be to fill black dirt around the edge to support and landscape to your desire, seed grass or rock (this covers the plastic edging. See the photo gallery for examples. Visit the Patio Store for items before and after your patio is completed, and learn more at Do It Yourself Forum.

Article Author: Hildebrand Construction
Printer Friendly Version

Paver Patio Discussion Forum on this Article!
Submit a comment, or ask a question Do It Yourself Forum - Landscape - Hardscape - Patio - Pavers

More Paver Patio Examples Below:

Paver Patio under a deck



Pavers Symetry Pattern
Pavers custom basketweavePavers Herringbone
For items before and after your Patio project, please visit the
Patio Store and More



support our troops